How To Open Davis And Deale Water Meters?

Quick Summary

In this blog post, we will explore how to open Davis and Deale water meters. We will discuss the two methods to turn off the water supply, including using the rotating valve on the side of the meter and accessing the cap screw valve by removing the blue lid. Precautions and considerations will also be highlighted, along with frequently asked questions to provide a comprehensive guide for opening Davis and Deale water meters.

Introduction

Welcome to Askly, your go-to source for answers to common questions. In this blog post, we will be discussing how to open Davis and Deale water meters. If you have a residential house equipped with one of these water meters and need to turn off the water supply for any reason, we’ve got you covered.

Davis and Deale Irrigation is a reputable company that specializes in developing innovative products related to water management. With their expertise in manufacturing high-quality water meters since 1980, they have become pioneers in the industry.

Understanding how to open Davis and Deale Water Meters can come handy when dealing with leaks or if there’s a need for shutting off the water temporarily. We’ll provide step-by-step instructions on two different methods recommended by experts from external sources:

Method 1 – Using the rotating valve:

On each meter’s side panel lies a rotating valve which controls its flow rate effectively.

• When the arrow on this valve points vertically up it means that it is currently opened allowing free passage of flowing liquid.
• To close off your home’s entire plumbing system simply rotate said handle clockwise at an angle of ninety degrees (90°).

Please note though; turning valves under pressure may prove difficult so take caution while doing so!

Method 2 – Accessing cap screw valves within:

If leakage originates inside rather than outside then accessing internal components becomes necessary instead! To do just follow these steps carefully;

1. Start by removing blue lid atop meter housing unit itself – pull upwards until detached completely
2. Once removed locate plastic cover cap situated beneath aforementioned topmost layer covering everything else below surface level too! Rotate counter-clockwise direction only using hands alone without applying excessive force onto anything whatsoever during process lest damage occur unnecessarily due improper handling techniques employed hereafter…
3. After successfully unscrewing protective casing exposing hexagonal-shaped capscrew-valve underneath proceed further as follows;
4. Insert 10mm Allen key into said opening and rotate it ninety degrees (90°) clockwise until water flow ceases entirely.

It’s important to note that these methods are designed for Davis and Deale water meters specifically. Other brands may have different mechanisms, so always refer to the manufacturer’s instructions if you’re unsure about your specific meter model.

In the next sections of this blog post, we will provide a detailed step-by-step guide on how to open Davis and Deale Water Meters using both Method 1 – Using the rotating valve, as well as Method 2 – Accessing cap screw valves within. We’ll also discuss precautions you should take while performing these actions. Stay tuned!

Understanding Davis and Deale Water Meters

Davis and Deale Irrigation is a renowned company that has been in the water-related products industry since 1980. They specialize in developing, manufacturing, marketing, and exporting innovative water solutions. With their extensive experience and expertise, they have become pioneers in designing micro irrigation sprayers, pool cleaners, water meters, and other essential developments.

One of the key areas where Davis and Deale excel is their production of high-quality water meters. These devices play a crucial role in accurately measuring the amount of water consumed by residential houses or commercial properties. By providing accurate readings on usage levels over time periods such as months or years; these meters help individuals monitor their consumption patterns effectively.

The commitment to quality at Davis & Deale can be seen through various aspects of their work process – from understanding client requirements to delivering cost-effective solutions without compromising on performance standards. They collaborate closely with local clients as well as international partners including government bodies responsible for managing public utilities like potable drinking-water supply systems. Through this collaboration, Davis & Deale successfully introduced engineering polymers into potable water systems, replacing traditional brass bodied valves, meters, and fittings. This innovation not only improves efficiency but also ensures durability while maintaining strict safety regulations regarding contact between polymer materials used within plumbing networks and potable drinking water supplies.

With an impressive track record backed up by numerous design awards won internationally for creating innovative polymer-based products related to the management of water resources, Davis & Deale earned recognition for their commitment towards providing quality solutions in the water industry. Their dedication towards continuous improvement reflects positively on the customer satisfaction they achieve by delivering superior products and reliable performance that meets the expectations of both local and international clients alike.

How to Open Davis and Deale Water Meters

Davis and Deale water meters are equipped with two methods for turning off the water supply in a residential house. These methods provide homeowners with options depending on their specific needs or circumstances.

Method 1: Using the Rotating Valve

The first method involves locating the rotating valve on the side of the meter. This valve is designed to control the flow of water into your property. When you need to shut off your water supply, follow these steps:

1. Locate the rotating valve on one side of your Davis and Deale water meter.
2. Check if there is an arrow indicator present on top of this valve.
3. If so, ensure that it points vertically up as this indicates that it’s currently in an open position allowing for normal flow.
4. To close off access from outside sources turn clockwise by 90 degrees until perpendicular (horizontal) to stop any further inflow.

It’s important to note that closing this type may be difficult under pressure due to its design; therefore, it’s recommended not attempting during high-pressure situations such as leaks or bursts where professional assistance should be sought instead.

Method 2: Removing Blue Lid & Plastic Cover Cap

If you suspect a leak within your Davis and Deale water meter itself, Method 2 provides an alternative solution:

Please proceed cautiously when following these instructions:

1. Firstly remove blue lid located at top part above dial mechanism. Pull upwards gently but firmly till released completely.
• This will expose plastic cover cap underneath which must also be removed in the next step.
• Note: Be careful while removing lids, as they can sometimes get stuck especially after long periods without maintenance. In case resistance is encountered, do not force removal rather seek help from professionals who have experience handling similar equipment.
2. Turn Counter-Clockwise To Remove The Plastic Cover Cap:

After removing the blue lid, you will see a plastic cover cap. This cap needs to be turned counter-clockwise in order to access the hexagonal-shaped cap screw valve beneath it.

3. Use A 10 mm Allen Key To Rotate The Cap Screw Valve:

Once the plastic cover cap is removed, insert a 10 mm Allen key into the exposed hexagonal-shaped opening. Then rotate this key by 90 degrees clockwise until water flow stops completely.

By following these steps carefully and correctly, you should successfully shut off your Davis and Deale water meter’s supply.

It’s important to note that if you are unsure about any of these methods or encounter difficulties during the process, it is recommended seeking professional assistance from plumbers or technicians who have experience working with Davis and Deale meters.

Step-by-Step Guide to Opening Davis and Deale Water Meters

Step 1: Identifying the location of the water meter

Before you can open a Davis and Deale water meter, it is important to locate its position. In most residential houses, the water meter is usually installed outside near the main entrance or in a designated utility area. Look for a small box-like structure with pipes connected to it.

Step 2: Method 1 – Turning off the water supply using the rotating valve

Once you have located your Davis and Deale water meter, look for a rotating valve on its side. This valve controls whether your water supply is open or closed.

To turn off (close) the water supply:

1. Turn this valve 90 degrees clockwise until it stops moving. This will shut down the flow of water through the meter and stop the supply to your house.
2. It’s worth noting that turning this valve may be difficult under pressure. If you encounter any difficulties in rotating the valve, you may need to use Method 2 described below.

Step 3: Method 2 – Opening the water meter to access the cap screw valve

If method one does not work due to difficulty in turning off the water supply under pressure or if your leak is from within the meter, it’s recommended to try method two. This method requires opening up the Davis and Deale meter by following these steps:

1. Remove the blue lid on the top of the meter. Pull it vertically upwards until it is completely detached from the rest of the mechanism. Be careful not to damage the lid during removal as it may snap suddenly if handled improperly.
2. Once you have removed the lid, you will see that there is a plastic cover cap on top of the measuring mechanism. Gently turn this cap counter-clockwise to unscrew it from the meter.
3. Underneath the cover cap, you will find a plastic hexagonal-shaped cap screw valve. This is the component that controls the water flow through the meter and can be used to close the water supply completely. Insert a 10mm Allen key into the hexagonal space of this valve.

Step 4: Using a 10 mm Allen key to rotate the cap screw valve and stop the water flow

With your Allen key inserted into the hexagonal space of the cap screw valve, gently turn it clockwise by rotating it 90 degrees until you feel resistance or hear a click sound.

This action will effectively shut off the water flow through the measuring mechanism, and you should notice that the supply to your house has stopped. If there is a leak within the measurement mechanism, this method allows you to isolate the leaking area without affecting the rest of the water supply system in your home.

Remember, to use Method 2 only if you encounter difficulties in using Method 1 or if your leak is from within the Davis and Deale meter itself. Always exercise caution when opening up any water meter and always have a professional plumber on hand if needed.

Precautions and Considerations

Turning off the water supply to a Davis and Deale water meter may sometimes come with certain difficulties, especially when there is pressure in the system. It’s important to be aware of these potential challenges so that you can take appropriate precautions.

Difficulties with Rotating Valve

When attempting to turn off the water supply using the rotating valve on the side of the meter, it might require some physical effort due to resistance caused by high-pressure situations. If you encounter difficulties or find it hard to rotate the valve 90 degrees clockwise, consider seeking assistance from a professional plumber who has experience dealing with such scenarios.

Beware of Criminal Activities

It’s also crucial for homeowners and residents equipped with Davis and Deale meters to be cautious about potential criminal activities involving their water meters. Criminals have been known at times remove valves on meters intentionally as part of schemes aimed at creating fountains or luring residents out of their properties under false pretenses. Stay vigilant if you notice any suspicious activity around your meter area, report it immediately to the authorities responsible for maintaining public safety.

Valve Removal by Joburg Water

Additionally, Joburg Water occasionally removes valves from residential properties where payment for services rendered hasn’t been made promptly enough. This practice helps prevent wastage while encouraging prompt settlement of outstanding bills within communities served by this utility provider.

To ensure smooth operation without interruptions related to either difficulty turning off supplies during emergencies or unauthorized tampering attempts, always keep an eye open regarding possible issues arising both internally (pressure) and externally (criminal acts).

References

1. https://www.rrva.net/environment/turn-off-your-water-supply/
2. https://www.davisanddeale.co.za/
3. http://www.davisanddeale.co.za/agb.html

Possible Related Questions:

How To Install A Geyser Step By Step How To Open Bull Brand Corned Meat How To Make Borehole Water Safe For Drinking How To Get Rid Of Hanging Belly After C Section